BSD-Chem C200 محلل الامتزاز الكيميائي الأوتوماتيكي

Standard Function

• Temperature Programmed Desorption (تي بي دي)
• Temperature Programmed Reduction (TPR)
• Temperature Programmed Oxidization (تبو)
• Temperature Programmed surface reaction (TPSR)
• Temperature Programmed Sulfidization (TPS)
• Pulse Titration
• Desorption Kinetics:
• Desorption activation energy (Ed)
• Preexponential factor A of desorption (Ad)
• Desorption order (n)
• Multi-temperature points
• Automatic ProgrammedReaction:
• Automatic cycle lifetime assessment;
• Programmable multi-step reactionprocess;
• Automatic multi-temperature points execution.

المعلمة التقنية

• Temperature programmed: program-controlled heating and cooling, rate: 1 centigrade/min to 100 centigrade/min;
• 2 high-temperature furnaces,range from room temperature to 1473K, two furnaces switch automatically and work for heating and cooling in turns;
• دعم 12 gas pipeline analysis;
• Mass Flow Controller (MFC): Support 3gas pipelines, support gas mixture chemistry adsorption;
• Adsorbate type: Non-corrosive and corrosive gas, vapour, الخ.,
• Test pressure: Standard Normal pressure; 1Mpa, 3Mpa, 10Mpa(اختياري);
• Pulse Titration: Standard measurable tube 0.5ml, optional1ml and 5ml;
• Vacuum pump: eliminate the effect of residual gas in free space of pipeline;
• Cold trap: eliminate effect of low-boiling point components vapor (على سبيل المثال. water) on concentration detection;
• Vapor Generator, generate vapor for chemisorption;
• Sample tube: Quartz U-shaped sample tube with temperature reference tube;
• Thermostat system: Double systems for thermostat, gas circuit system support from 313Kto 353K while TCD system supports from 333K to 383K;
• External marked sampler: Standard 1ml sampler; other volumes (اختياري);
• Two combustible gas alarms: Monitor different areas in real-time, avoiding leakage of combustible gas;
• Two detection modes of TCD detector: Support switching high sensitivity mode and wide range mode, meet test’s requirement of weak signal and strong signal;
• Detection system: default TCD detection system, Optional MS detection and infrared system.

هيكل مميز

المزايا التقنية

• Full automatic test：dual heating furnace automatic switching, no need to wait for pre-treatment cooling, directly switch to the other furnace for testing, without human intervention;
• Vacuum clean residual gas: built-in vacuum pump to remove residual gas in free space, reduce baseline drift and improve test accuracy;
• Temperature reference tube: temperature sensor is placed in reference tube of the sample tube (the sensor and sample are in the same environment), ensure high accuracy of temperature control and measurement.
• Automatic air-cooled cooling system:equipped with an air-cooled tube and a temperature detector at the air-cooled site, automatically detect the temperature of the heating furnace and turn on the air-cooled cooling system to prepare for the next test;
• Multi-step continuous automatic test: fully automatic execute edited multi-step test program, used to evaluate the catalytic performance and chemical adsorption performance of materials under complex reaction conditions;
• Automatic cycle test: pre-treatment and test automatically cycle, used to evaluate the lifetime and chemisorption stability of materials;
• Support ultra-low temperature thermostat & ultra-low temperature programmed temperature rising, realize ultra-low temp test;
• High standard configuration: standard vapor generator, pulsed titration system;
• Support test of mixing 3 analysis gas, standard 3 gas MFC and support 3-gas mixture test;
• High reliability and durability;

Comparison test result

Application data report

 

 

For right graph: Three NH₃ desorption peaks appeared at 463K, 723K,1173K; if the desorption peak at 1173K is NH₃’s, it is not in line with the characteristic of the material and expectations of the researchers.

For left graph: Two NH₃ desorption peaks appeared at 463K and 723K while small amount of H₂O desorption, the desorption peaks at 1173K is the H₂O’s, in line with characteristic (Not desorb NH₃ )of the material.

 

For right graph: Three NH₃ desorption peaks appeared at 398K,623K and 973K;

For left graph: NH₃ desorption peak appeared at 398K; small NH₃ desorption peak appeared at 623K; H₂O desorption peak appeared at 513K; CO₂ desorption peak appeared at 623K; CO desorption peak appeared at573K and 973K;

 

Coupled with on-line mass spectrometer and Infrared

 

• Mass spectrometry interface;
• Real time monitor in TPSR;
• Obtain concentration curve.

• FT-IRinterface, optional model Nicolet iS20，Nicolet Summit (ThermoFisher)
• Optional gas accessories,
• Optional solid accessories;